Should Vinyl Plank Go Under Kitchen Cabinets? What SPC Install Guides Say
By the East Cleveland Flooring team
Short answer: no. Every SPC vinyl plank install guide we read says to install the floor around fixed kitchen cabinets and islands, not under them, and to leave the expansion gap at the cabinet base. Rigid core vinyl plank is a floating floor: it has to move a little with temperature, and a run of base cabinets or an island full of granite sitting on top of it pins it in place.
We went back through six published SPC installation guides we read in November 2026 and summarized what each says about cabinets below. Your plank's own guide is the one that counts. East Cleveland Flooring installs SPC luxury vinyl plank as a floating floor, so this is the rule we work to in kitchens.
What six SPC install guides say about cabinets
Guide | Cabinets and islands |
|---|---|
Permanent cabinets, vanities, islands and similar items should be installed first, then SPC installed around them with the proper expansion gap. Can go under vanities with legs. | |
Same wording: install cabinets, vanities and islands first, then the floor around them. | |
Install planks 1/4" away from walls, cabinets and pipes. Base cabinets should not be installed on top of the planks. | |
Do not install under permanent kitchen cabinets. Wall molding and transitions cannot be fastened to the planks. | |
Do not install cabinetry, an island or peninsula counters, vanities, tubs and showers on top of the floor. Install around them with the expansion relief in the instructions. | |
Do not install fixed objects such as cabinets, islands or wall units on top of the flooring, or fasten trim directly to the floor. |
Halstead and Europine word it as an order of work: cabinets first, then the floor. Bruce, Cancork, InStride and Southwind word it as a prohibition: nothing fixed on top. Same result either way.
Why a floating floor can't carry cabinets
It needs to move. The guides call for a gap at walls and other vertical objects (1/4" in the Bruce, Halstead and Bering guides; InStride's minimum is 5/16") so the floor can expand and contract. A cabinet set on top turns part of the floor into a fixed point.
A pinned floor can buckle or open at the seams. If one area can't move, the stress shows up somewhere else, often as a peak or gap a few feet away. Our post on why an LVP floor buckles covers that in detail.
Repairs get harder. If a plank under a cabinet is ever damaged, the cabinet has to come out to reach it.
What this means for the order of a kitchen job
Cabinets staying. The floor goes in around the existing cabinets and island. The gap at the toe kick gets covered by base shoe or quarter round fastened to the cabinet, not to the floor. Southwind's guide says baseboard goes into the wall and quarter round into the baseboard, never into the floor.
Cabinets being replaced. Set the new cabinets on the subfloor first, then install the plank around them. That also means the cabinet installer has to set them level on the subfloor and allow for the finished floor height at the dishwasher and range openings.
A vanity with legs is different. Halstead says SPC can be installed under vanities with legs, because a leg doesn't pin a whole run of floor the way a cabinet box does. A built-in vanity still gets the floor around it.
Check the dishwasher and range openings
Our stocked plank is 4.5 MM thick. If the plank runs into the dishwasher bay and the dishwasher has to come out later, it now has that much less room under the countertop. Before install day, decide with whoever handles the appliances whether the floor runs into the dishwasher bay or stops at the cabinet face, and measure the opening. The same goes for a slide-in range between two cabinets. Our post on moving a fridge or stove onto new vinyl plank covers getting heavy appliances back in without damaging the floor; the fridge itself is a moving appliance, not a fixed cabinet, and sits on the floor normally.
Open kitchens and long runs
Kitchens open to a dining or living room often make one long floating floor. Some guides set limits on how far one floor can run before it needs an expansion break: InStride calls for a T-molding once the floor goes more than 100 feet in any single direction, and Bering caps a continuous area at 3,000 square feet and 55 linear feet without a T-mold break. An island in the middle doesn't count as a break; the floor still has to be free to move around it. Read about transition strips at doorways for where breaks usually go.
Water at the sink base
SPC is a waterproof plank, but the Halstead guide says it should not be used to seal an existing floor from moisture and can't prevent mold or structural problems from leaks. Before a kitchen floor goes in, look inside the sink base for a stained or soft cabinet bottom and a dripping trap or supply line. Fix the leak first. If the subfloor in front of the sink feels soft, it needs repair before plank; see how flat a subfloor needs to be for LVP.
What a kitchen floor costs with us
East Cleveland Flooring charges $2.49 per sq ft for our plank plus our $3.00 per sq ft labor-only install special, on jobs of 700 sq ft or more. We don't take jobs under 700 sq ft, and a kitchen alone is rarely that big, so kitchens are usually part of a bigger room list. A made-up example: kitchen 150, dining room 150, living room 300, hall 100 sq ft is 700 sq ft, which is $3,843.00 with our plank, or 25 cartons at 28.68 SF/CT before cut waste. Prices don't include tearing out old flooring, moving cabinets or subfloor repair. Try other sizes in our LVP cost calculator.
When you ask for a quote, tell us whether the cabinets and island are staying, being replaced or not installed yet, because that decides the order of work. Then use our LVP installation prep checklist before install day.
See LVP installation in Cleveland and East Cleveland or call (216) 238-5999. $500 gets you on the schedule and counts toward the 50% booking payment.
East Cleveland Flooring
Phone: (216) 238-5999 · Email: [email protected] · Monday to Saturday, 8 AM to 6 PM