Do You Need Transition Strips at Doorways With Vinyl Plank?

November 16, 2026•5 min read

By the East Cleveland Flooring team

Short answer: not at every doorway. A floating vinyl plank floor can usually run through a doorway into the next room without a strip. You need a transition where the plank meets a different floor (carpet, tile, an old threshold), and wherever the floor runs longer than your plank maker allows in one direction. In the SPC guides we read, that limit ranges from 39 feet to 100 feet, so the paperwork for your plank decides it.

We install SPC plank with a floating installation, so this comes up on nearly every job with more than two rooms. Below is what four manufacturers' installation guides say (read November 14, 2026), how to handle doorways, and the mistakes we see.

What the guides say about when a transition is required

Guide

When a transition is required

Gap at walls

Cancork SPC rigid core

"Areas over 39' long or 39' wide need transition pieces."

3/8"

Europine SPC

T-molds required in a room or area larger than 50 lineal ft in any direction, so sections are no larger than 50 ft x 50 ft

1/4"

Halstead generic SPC

Its spec table says larger than 50 lineal ft in any direction; its finishing section says larger than 100 lineal ft

1/4"

Bruce Rigid Core SPC 2G

No length limit stated; says a T-molding "or similar" is preferable at doorways and where planks meet other floors

1/4"

Notice the Halstead guide gives two different numbers in the same document. When that happens, plan for the stricter one or ask the manufacturer. The guide that ships with your plank is the one its warranty points to.

How to measure "in any direction"

The limit is about one continuous run of floor, not one room. If your plank runs from the front door through the living room, dining room and kitchen without a break, add those lengths together along the line the floor travels. A typical house rarely hits 39 feet in one room, but an open first floor of a large house, or a long hallway that connects rooms, can. If the continuous run is over your plank's limit, the guides call for a T-molding to break it into sections, and a doorway is often the neatest place to put that break.

Doorways: what to do with and without a strip

  • Same floor both sides, under the limit: the plank can usually run straight through. Undercut the door jambs and wood casings so the plank slides under them. Halstead and Europine say to use a handsaw laid flat on a scrap plank, and to never undercut metal door casings.

  • Metal door frames: leave the expansion gap around the metal frame instead. Halstead's guide says to keep a minimum of 1/4" around all fixed objects, cabinetry and metal door jambs.

  • Different floor on the other side: use a molding made for that change. Bruce and Cancork both say a T-molding "or similar" is preferable at doorways and where plank meets another surface, covering the edge without pinching the planks.

  • Breaking a long run: a common choice is to center the T-molding under the door, where it reads as a threshold.

The rule every guide agrees on: don't pin the floor

A floating floor has to move a little with temperature. Every guide we read says moldings must not lock it down:

  • Bruce: transition moldings "should not pinch the flooring against the subfloor," and molding is nailed "to the wall surface, not through the flooring."

  • Cancork: "Wall molding and transitions cannot be fastened to the planks/tiles."

  • Halstead: cover expansion spaces "being sure not to trap or pin down the floor. Nails should go into wall, not the floor."

A transition screwed through the plank, or a heavy threshold set tight on top of it, is one of the causes we cover in why LVP floors buckle.

Stairs and step-downs

Where plank meets the top of a stair, the Halstead and Europine generic guides list installation on stairs or vertical surfaces as voiding the warranty, while Cancork says flooring "should be glued down on stairs." So stairs follow your plank's own rules, and a floating floor usually stops at the top step with a molding. Ask before you buy if stairs are in the plan.

Mistakes we see at doorways

  • Butting plank tight to the old threshold. No gap means nowhere to expand.

  • Nailing quarter round into the floor. Nail it to the baseboard or wall.

  • Cutting into a metal casing. The guides say never undercut metal casings.

  • Running one floor through a huge open area without checking the plank's limit.

  • Forgetting the door. New plank can raise the floor at a doorway. Check that each door still swings and latches before the job is called done.

What we install

When we supply the material, it's SPC plank, 7" x 48", 12 MIL, 4.5 MM, floating installation, at $2.49 per sq ft plus our $3.00 per sq ft labor-only install special, with a 700 sq ft minimum. Tell us where your floors change and which doors have metal frames, and we'll cover transitions and moldings on your quote. See also how to fix gaps in LVP flooring and our LVP installation prep checklist. Ready for a price? Visit LVP installation in Cleveland or call (216) 238-5999.

East Cleveland Flooring
Phone: (216) 238-5999 · Email: [email protected] · Monday to Saturday, 8 AM to 6 PM

Custom HTML/CSS/JavaScript
blog author avatar

ccmedia

Author of East Cleveland Flooring Blog posts.

Back to Blog