Why Is My LVP Floor Buckling? Causes, Fixes and How to Prevent It
By the East Cleveland Flooring team
Short answer: a floating LVP floor usually buckles, peaks or lifts because something is stopping it from moving. Rigid core (SPC) plank expands and contracts with temperature, so manufacturers require an expansion gap at every wall and vertical object and forbid pinning the floor down with cabinets, islands, nails or screws. When the gap is missing, filled or covered by trim nailed into the floor, the planks push against each other and rise. Find what's pinning the floor, free it, and the planks often settle back down.
This guide is from the East Cleveland Flooring team. It draws on four manufacturers' SPC installation guides (Bruce, InStride, Southwind and Bering), read November 2026. Always follow the guide for the plank in your house; they don't all say the same thing.
Why a floating floor needs room to move
Click-lock SPC is installed "floating": the planks lock to each other, not to the subfloor. That's what lets them expand and contract. The Bering guide puts it plainly: never put nails or screws, "including door stops," into the flooring or the expansion zone, because "they will prevent proper expansion and contraction of the structure and flooring." The InStride guide says "DO NOT glue, nail, screw or fasten to substrate."
In Cleveland, a floor goes through heated, dry winter air and humid summers, and rooms with big sunny windows or radiators swing more than others. That's why a floor that looked fine in October can peak in July, or the other way around.
The most common causes
Cause | What you'll see | What the guides say |
|---|---|---|
No expansion gap, or a gap filled tight | Peaking along a wall or across a doorway | Bruce and Bering: 1/4" from walls and all vertical objects. InStride: 5/16" (8 mm) minimum. |
Cabinets, islands or vanities set on the planks | Lifting or gapping near the kitchen or bath | InStride: don't install cabinetry, islands, vanities, tubs or showers on top. Bruce: base cabinets shouldn't sit on the planks. Southwind: no fixed objects on top. |
Trim or transitions fastened through the floor | A ridge near baseboard or a threshold | Southwind: nail baseboards into the wall and quarter round into the baseboard, never into the floor. Bruce: transition moldings shouldn't pinch the flooring. |
Door stops screwed into the plank | A bump or crack behind a door | Bering: never, including door stops. |
A run that's too long without a break | Buckling in the middle of a big open area | Bering: a T-mold break beyond 55 linear feet or 3,000 sq ft, and at all doorways. InStride: a T-molding beyond 100 feet in one direction; doorway transitions not required except over radiant heat. |
Heat and direct sun | Buckling or fading in front of windows | InStride: failing to shade or UV-tint windows "can discolor, fade, or buckle vinyl planks." Southwind: a 5/8" gap where areas get over 100°F. |
Water is a separate problem. If the floor lifted after a leak or a wet subfloor, find and fix the moisture source first; our post on how flat a subfloor needs to be for LVP covers what has to be right underneath.
The guides don't agree, and that matters
Notice the differences in the table: one guide wants a T-molding at every doorway and a break every 55 feet; another says doorway transitions aren't required and allows runs to 100 feet. Neither is wrong for its own product. But if a floor was installed to one brand's rules using another brand's plank, it can fail. If you bought the plank yourself, keep the carton or the brand name and find that manufacturer's guide before anything is cut.
How to find what's pinning your floor
Look where the buckle starts. Along one wall suggests that wall's gap. Near the kitchen points to the cabinets or island. In a doorway, check the transition and the door stop.
Pull back a piece of quarter round near the buckle. If the plank is tight against the wall or there's a nail through the plank, you've found it.
Check under transitions for screws through the plank.
Look for heavy fixed items: a built-in, a pantry unit, an island or a vanity set on the floor.
Note the room's conditions: sun through big windows, a nearby radiator, an unheated space. Our post on LVP around radiators and heating pipes covers the gaps those need.
Fixing it
Restore the gap. Trim the planks back from the wall or object to the gap the guide calls for, then reinstall the trim nailed into the wall.
Free the floor from fixed objects. That can mean cutting the floor around a cabinet or island rather than running under it.
Add a break where a run is longer than the guide allows.
Remove fasteners through the plank, including door stops; mount door stops on the wall or baseboard instead.
Replace damaged planks. Planks with broken locking edges often won't lie flat again. Our post on how to fix gaps in LVP flooring covers the reverse problem.
If the planks stay lifted after the floor is freed, call an installer before forcing them down.
Installing a new floor
The plank we supply is SPC, 7" x 48", 12 MIL, 4.5 MM, floating installation. We install LVP at $2.49 per sq ft for our plank plus our $3.00 per sq ft labor-only install special, or $3.00 per sq ft if you supply the plank, on jobs of 700 sq ft or more. If you're supplying the plank, tell us the brand and keep its installation guide with the cartons. See our LVP installation in Cleveland page for the details, and installing LVP in cold weather for the temperature rules before and after install.
$500 gets you on the schedule and counts toward the 50% booking payment. Call (216) 238-5999.
East Cleveland Flooring
Phone: (216) 238-5999 · Email: [email protected] · Monday to Saturday, 8 AM to 6 PM