Installing LVP Around Radiators and Heating Pipes: Gaps, Cutouts and Old Pipe Wrap

November 11, 2026•6 min read

By the East Cleveland Flooring team

Short answer: click-together SPC vinyl plank goes around radiators and heating pipes, never under or pinned by them. Leave the expansion gap your plank's instructions call for at every pipe and radiator foot (one common SPC guide says 1/4 inch; another says 5 mm), drill pipe holes 1/2 inch bigger than the pipe, and cover the gaps with trim or pipe collars. Whether a radiator stays put or gets lifted out is a heating decision to make before install day, not during it.

This comes up constantly in older Cleveland-area houses heated by a boiler, where cast-iron radiators sit in most rooms and supply pipes rise through the floor. East Cleveland Flooring installs LVP in those houses, and this is how we think through the heating parts of a job. For the install itself, see our LVP installation page for Cleveland and East Cleveland.

What SPC installation instructions say about pipes and fixed objects

Two published SPC installation guides, as examples (your plank's own instructions are the ones that count):

  • United Weavers' Click Lock SPC instructions call for "Expansion spacing of 1/4" (6mm) where flooring abuts all vertical surfaces," with the tip: "When installing around pipes, drill the holes 1/2" (12mm) larger than the diameter of the pipes." They also say: "Do not install cabinets, islands or fixed objects on top of the flooring; flooring should be butted to these with proper expansion spacing," and not to fasten wall moldings or transition strips to the planks.

  • Signature Flooring's SPC instructions say to "leave a 5mm / 0.2" expansion gap between walls and fixtures, such as pipes and pillars, stairs, etc.," with the same 1/2-inch pipe-hole tip.

The reason is the same in both: a floating floor moves slightly with temperature. If a heavy radiator sits on the plank, or a pipe is pressed tight against the cut edge, that spot can't move with the rest of the floor. The strain shows up as joints that open, peak or won't stay closed. Our post on why gaps open in LVP flooring covers what that looks like.

United Weavers also asks for at least 18 inches of distance from "heat sources such as fireplaces, wood stoves, furnaces, etc." Radiators aren't named in either guide we checked, so if your plank will run close to one, ask the plank's manufacturer what clearance they want rather than guessing.

Option 1: leave the radiator in place and cut around it

This is the usual choice when the radiator is in good shape and nobody wants to touch the heating system.

  1. The radiator's feet stay on the subfloor. The plank is cut around each foot with the expansion gap all the way around, so the radiator's weight never rests on the floating floor.

  2. The supply and return pipes get holes drilled 1/2 inch larger than the pipe, per the guides above.

  3. The plank is cut from its edge through each hole so it can slide around the pipe, and the small cut piece is set back in behind the pipe.

  4. Pipe collars (round covers that snap around the pipe) hide the gap. They sit over the plank, not fastened through it.

Two things to check first: whether there's room to work under the radiator (some sit very low), and whether the floor under it is in decent shape. You can't fix a rotten subfloor under a radiator that isn't moving.

Option 2: have the radiator lifted out first

Pulling a radiator gives clean, continuous plank underneath and a chance to fix the subfloor, but it means draining and disconnecting part of the heating system and reconnecting it afterward. That's heating work, not flooring work. East Cleveland Flooring installs LVP only, so if you go this way, line up a qualified heating contractor or plumber, agree who reconnects the radiator and when, and make sure the house still has heat on install day (see below). Cast-iron radiators are also very heavy, so plan how it will be moved and where it will wait.

Old pipe wrap: the pitfall to stop and check

Heating pipes in older houses are often wrapped in old insulation, sometimes right where they pass through the floor. Don't cut, scrape or pull that wrap to make room for a plank.

  • The U.S. EPA's asbestos guidance for homeowners says you generally can't tell whether a material contains asbestos by looking at it, and "If in doubt, treat the material as if it contains asbestos and leave it alone." It notes that pipe, furnace and boiler insulation can sometimes be sealed rather than removed, by a trained professional.

  • In Ohio, a business that removes, repairs or encapsulates friable asbestos-containing material in amounts over 50 linear feet or 50 square feet must be licensed by Ohio EPA as an asbestos hazard abatement contractor, according to Ohio EPA's contractor license fact sheet.

  • Local inspectors notice it too. Cleveland Heights' housing inspection checklist, for example, says "Damaged/hanging insulation on the boiler or heat pipes should be encapsulated or removed."

If the wrap near your floor is damaged or you're not sure what it is, have it looked at by a trained asbestos professional before the flooring job is scheduled. A floor installer is the wrong person to make that call, us included.

Keep the heat on before and during the install

SPC plank has a temperature range for installation. United Weavers, for example, says service temperatures "must be maintained consistent between 60°F to 85°F" before and during installation. In a boiler-heated house that means the boiler has to be running and the radiators in the work rooms connected, which is another reason to finish any radiator removal and reconnection on a plan. Our guide to installing LVP in cold weather covers vacant units where the heat has been off.

Mistakes we see around radiators and pipes

  • Running plank tight to the pipe. It looks neat on day one, then the floor has nowhere to move.

  • Setting a radiator back down on the new floor. That pins a floating floor, exactly what the instructions warn against.

  • Caulking or nailing pipe collars and trim through the plank. Trim covers the gap; it shouldn't fasten the floor down.

  • Deciding about radiator removal on install day. Draining and reconnecting heat is its own job with its own trade.

  • Disturbing old pipe wrap to fit a cut. Stop and get it checked.

What to tell us when you ask for a quote

  • How many radiators are in the rooms you want done, and whether each one stays in place or is being lifted out by your heating contractor.

  • Where pipes come up through the floor, plus a photo of each.

  • The condition of any pipe wrap near the floor.

  • Whether the heat is on now (and will be on install day).

  • Room sizes. Our post on how to measure a room for LVP helps.

Our pricing is $2.49 per sq ft for our plank and a $3.00 per sq ft labor-only install special, with a 700 sq ft minimum job. When we supply the plank, it's 7" x 48" SPC, 12 MIL, 4.5 MM, floating installation. We install Monday through Saturday, 8 AM to 6 PM. $500 gets you on the schedule and counts toward the 50% booking payment. Before install day, run through our LVP installation prep checklist.

$500 gets you on the schedule and counts toward the 50% booking payment.

Call (216) 238-5999 or email [email protected], or start at our LVP installation page.

East Cleveland Flooring
Phone: (216) 238-5999 · Email: [email protected] · Monday to Saturday, 8 AM to 6 PM

Custom HTML/CSS/JavaScript
blog author avatar

ccmedia

Author of East Cleveland Flooring Blog posts.

Back to Blog